Measurement of Surface and Shallow depth Changes of Polypropylene Due to Gliding Discharge Plasma

Yahaghi, Effat; Azizi, Maryam; Nori Dogahi, Seyedeh Maryam; Bakhtiari Ramezani, Mahdieh; Biganeh, Ali

Measurement of Surface and Shallow depth Changes of Polypropylene Due to Gliding Discharge Plasma

Document Type : Original Research

Authors

E. Yahaghi ¹

M. Azizi ¹

S. M. Nori Dogahi ¹

M. Bakhtiari Ramezani ²

A. Biganeh ³

¹ Department of Physics, Imam Khomeini International University, Qazvin, Iran

² Fusion Department, Nuclear Science and Technology Research Institute, Tehran, Iran

³ Department of Physics and Accelerators Research Institute, Nuclear Science and Technology Research Institute, Tehran, Iran

Abstract

Research subject: Polypropylene (PP) is a thermoplastic polymer that is used in a wide range of applications, including films and sheets, blow molding, injection molding, food packaging, textiles, laboratory and medical equipment, pipes, industrial and construction applications, and the manufacture of automotive components. In the applications of this polymer, improving the surface of PP has been considered. One of the usual methods for improving the surface is the cold plasma method. Plasma is a chemically highly active environment where there are many ions and radicals. In this research, atmospheric pressure gliding discharge plasma was used to increase the hydrophobicity of PP and the surface and depth changes of PP were investigated.

Research approach: The depth and surface changes of PP were investigated by radiating the gliding discharge plasma to the PP polymer surface at the different times. FTIR and XRD tests were performed to investigate volume changes and FESEM investigated the surface changes. The hydrophobicity of PP was investigated by contact angle (CA) test and positron lifetime spectroscopy (PALS) was used to investigate shallow depth changes.

Main results: The results show that the applied cold plasma did not cause volumetric changes in PP, but caused surface changes and roughness. In this polymer, the contact angle has increased from 30.1 ± 0.1 to 34.4 ± 0.1 and the hydrophobicity of the surface has increased. Examining the changes in holes by PALS test shows that after plasma irradiation the volume of the holes increased from 217 Å³to 222 Å³ and their intensity decreased. This is due to the heat of the plasma and the energy of its particles.:

The results show that the cold plasma caused surface and depth changes and the contact angle increased from 30.1 ± 0.1 to 34.4 ± 0.1 and the hydrophobicity of the surface increased.

Keywords

plasma

Polymer

Polypropylene

Subjects

Processing

1. اعظم رحیمی، آشنایی با پلیمرها و کاربرد آنها ، پژوهشگاه پلیمر و پتروشیمی ایران، 1384
2. تری ال، ریچارد سون، پلاستیک‌های صنعتی، مترجمان: شیرین خسروی، مرتضی مضطرزاده، سازمان پژوهشهای علمی و صنعتی ایران، انتشارات یزد.
3. Adamson A. W., Alice A. P., and Gast P., Physical Chemistry of Surfaces, Wiley, USA, Chap. 12, 1997.
4. Khoee S. and Bageri Y., Surface Modification of Magnetite Nanoparticles via Click Reaction for Biomedical Application, Polymerization (In Persian). 5, 16-26, 2014.
5. Ali A.M., Hassan M.A.A., for Efficient Treatment of Industrial and Wastewater Sluge, Int. Organ. Sci., 10, 63-75, 2016.
6. Borcia C., Borcia G., Dumitrascu N., Plasma Induced Surface Modification in Relation to Polymer Characteristics, J. Optoelectron. Adv. Mater., 10(3), 675–679, 2008.
7. Fridman A., Nester S., K. Lawrence A., Saveliev A., Mutaf-Yardimci O., Gliding Arc Gas Discharge, Progress in Energy and Combustion Science, 25, 211–231, 1999.
8. ا. حاجی، ا. موسوی شوشتری، مقدمه ای بر عمل آوری با پلاسما و کاربرد آن در اصلاح خواص سطحی الیاف پلی پروپیلن، مجله علمی - ترویجی علوم و فناوری نساجی، سال چهارم، شماره ،4زمستان 1
9. Tuomisto F., Defect Identification in Semiconductors with Positron Annihilation: Experiment and theory, Rev. Mod. Phys., Vol. 85, No. 4, October–December 2013, pp. 1-49.
10. Mansuroglu D., Uzun-Kaymak I. U., Argon and nitrogen plasma modified polypropylene: Surface characterization along with the optical emission results. Surface and Coatings Technology, 358, 551–559, 2019.
11. Altuncu E., Üstel F., Esen S.G., Karayel E., Influence of oxygen and nitrogen plasma treatment on polypropylene (PP) bumper surface, Journal of Achievements in Materials and Manufacturing Engineering 77/1,18-23, 2016.
12. Pettersb K., Krause-Rehbergb R., Asharaful Alamd M., Studies of Interdiffusion in Polymer Blends by PALS, Radiation Physics and Chemistry, 68, 369–373, 2003.
13. Chen Zh., Wang Zh, Fu Q., Ma Zh, Fang P., He Ch., Microstructure and Surface State of Plasma-treated High-density Polyethylene Elucidated by Energy-tunable Positron Annihilation and Water Contact Angle Measurements, The Japan Society of Applied Physics, Proc. 2nd Japan-China Joint Workshop on Positron Science, JJAP Conf. Proc. 2, 011202 (2014) doi:10.7567/JJAPCP.2.011202
14. Gomathi N., Rajasekar R., Rajesh Babu R., Mishra D., Neogi S., Development of Bio/Blood Compatible Polypropylene Through Low Pressure Nitrogen Plasma Surface Modification; Materials Science and Engineering C 32 1767–1778, 2012.
15. Andrei V. Smirnov, Vsevolod S. Atkin1, Ilya A. Gorbachev, Alexander I. Grebennikov, Ilya V. Sinev and Viatcheslav V. Simakov., Surface Modification of Polystyrene Thin Films by RF Plasma Treatment; BioNanoSci. 7:680-685, 2017.
16. Novák I., Florián Š. Investigation of long-term hydrophobic recovery of plasma modified polypropylene. Journal of Materials Science 39, 2033–2036, 2004.
17. Lehocký M, Drnovská H., Lapčı́ková B. Barros-Timmons A.M, Trindade T., Zembala M, Lapčı́k Jr L, Plasma Surface Modification of Polyethylene, Colloids and Surfaces A: Physicochemical and Engineering Aspects, Volume 222, Issues 1–3, 30 July 2003, Pages 125-131
18. Biganeh A., Kakuee O., Rafi-Kheiri H., Lamehi-Rachti M., Sheikh N., Yahaghi E., Positron Annihilation Lifetime and Doppler broadening Spectroscopy of Polymers, Radiation Physics and Chemistry 166 ,2020, 108461.‏ https://doi.org/10.1016/j.radphyschem.2019.108461
19. Azizi M., Bakhtiari Ramezani M., Yahaghi E., Nohekhan M., Effect of Plasma on Polyethylene by Positron Lifetime Spectroscopy, Iran. J. Polym. Sci. Technol., (In Persian), 35, 4, 380-390, 2022, DOI: 10.22063/JIPST.2022.3182.2162.