Simulation of Hydrogel Injection in Micro-Model and Prediction of Oil Recovery Factor

Hayatolgheibi, Hosein; Ameli, Forough

Simulation of Hydrogel Injection in Micro-Model and Prediction of Oil Recovery Factor

Document Type : Original Research

Authors

H. Hayatolgheibi ¹

F. ameli ²

¹ Iran university off Science and Technology

² Iran university of Science and Technology

Abstract

Research Subject: Global energy demand is increasing, so enhanced oil recovery techniques have incorporated in production processes. Water flooding is a common technique in oil recovery processes. One of the major challenges in this technique is heterogeneity of the reservoir structure which results in increased water production and reducing the oil recovery factor. Moreover, long-term water or chemical injection might lead to the increased horizontal and vertical heterogeneities in the reservoir. Selective blockage of high permeability areas and consequently improved production from low permeability regions is important for increasing the oil recovery factor. In recent years, using hydrogels in injection processes, has been associated with various field successes, indicating the ability of these materials for selectively blocking the areas of high permeability. Hydrogels are injected after water or polymer flooding to conduct the injected fluid to low permeability areas.

Research Approach: In this paper, hydrogel injection process was simulated in glass micromodels using Comsol Multiphysics software. Hydrogel functionality was studied in low permeability areas in porous media. Moreover, the optimized conditions for water flooding process was studies. For this purpose, after model validation, sensitivity analysis was performed on effective parameters on oil recovery factor and a mathematical model was presented to predict the oil recovery factor.

Main Results: Oil recovery factors obtained from experimental and simulation studies, were in good agreement with each other with absolute error values of 2.29% and 4.06%, for water and hydrogel flooding, respectively.

Four parameters of injection rate, contact angle, oil viscosity, and injection fluid viscosity were considered as effective parameters on oil recovery factor. Among them, contact angle was the most important parameter. In water flooding, the most important interacting parameters are viscosity and contact angle and the least important parameters are injection temperature and rate. In water flooding simulation studies, the thickness of the contact surface was obtained hmax/5, where is 230 micrometers. For hydrogel injection, the contact surface thickness was obtained terpf.ep_default / 5.65. Terpf.ep_default is the thickness of contact surface, equal to 631 micrometers

Keywords

Enhanced oil recovery

Phase-Field Method

Hydrogel

simulation

Comsol Multiphysics

Subjects

enhanced oil recovery

1. Pu, J., et al., Development of Thermotransformable Controlled Hydrogel for Enhancing Oil Recovery. Energy & Fuels,. 31(12),13600-13609, 2017
2. Imqam, A. and B. Bai, Optimizing the strength and size of preformed particle gels for better conformance control treatment. Fuel,. 148,178-185, 2015
3. Ren, P., Li, J., Zhao, L., Wang, A., Wang, M., Li, J.,& Bai, S. Dipeptide self-assembled hydrogels with shear-thinning and instantaneous self-healing properties determined by peptide sequences. ACS applied materials & interfaces, 12(19), 21433-21440, 2020
4. Amiri, H.A. and A.A. Hamouda, Evaluation of level set and phase field methods in modeling two phase flow with viscosity contrast through dual-permeability porous medium. International Journal of Multiphase Flow,. 52,22-34, 2013
5. Amiri, H.A. and A.A. Hamouda, Pore-scale modeling of non-isothermal two phase flow in 2D porous media: Influences of viscosity, capillarity, wettability and heterogeneity. International Journal of Multiphase Flow, 61,14-27, 2014
6. Wu, Y.-S. and B. Bai. Modeling particle gel propagation in porous media. in SPE Annual Technical Conference and Exhibition.. Society of Petroleum Engineers, 2008
7. Liu, J., Li, L., Xu, Z., Chen, J., & Dai, C. Self-growing Hydrogel Particles with Applications for Reservoir Control: Growth Behaviors and Influencing Factors. The Journal of Physical Chemistry B, 125(34), 9870-9878, 2021.
8. El-Hoshoudy, A. N. Experimental and Theoretical Investigation of Glycol-Based Hydrogels through Waterflooding Processes in Oil Reservoirs Using Molecular Dynamics and Dissipative Particle Dynamics Simulation. ACS omega.2021
9. Elsaeed, S. M., Zaki, E. G., Omar, W. A., Ashraf Soliman, A., & Attia, A. M. (2021). Guar Gum-Based Hydrogels as Potent Green Polymers for Enhanced Oil Recovery in High-Salinity Reservoirs. ACS omega, 6(36), 23421-23431.
10. جمالی, م.م.ن., ساخت و بررسی ژل پلیمر هوشمند حاوی نانوذرات با قابلیت استفاده در ازدیاد برداشت نفت دانشگاه علم و صنعت, 156., 1392
11. Mauri, R., Non-Equilibrium Thermodynamics in Multiphase Flows, Springer Science & Business Media, 2012
12. Akhlaghi Amiri, H.A. Pore-level Influence of Contact Angle on Fluid Displacements in Porous Media. in COMSOL Conference, 2014
13. Jamali, A., et al., Synthesis and characterization of pH‐sensitive poly (acrylamide‐co‐methylenebisacrylamide‐co‐acrylic acid) hydrogel microspheres containing silica nanoparticles: Application in enhanced oil recovery processes. Journal of Applied Polymer Science, 137(12), 484-491, 2019