Investigation of the TPS Effect on the Biodegradability of Agricultural Mulches Based on PLA and LDPE

Shahabi Ghoyonloe, Mohammad; Khojastehpour, Mehdi; Sadrnia, Hassan; Ghasemi, Ismaeil

Investigation of the TPS Effect on the Biodegradability of Agricultural Mulches Based on PLA and LDPE

Document Type : Original Research

Authors

M. Shahabi Ghoyonloe ¹

M. Khojastehpour ²

H. sadrnia ²

I. Ghasemi ³

¹ PhD student in Ferdowsi University of Mashhad

² Faculty Member of Ferdowsi University of Mashhad

³ Faculty member of Iran Polymer and Petrochemical Institute

Abstract

Abstract

Research subject: The need to increase agricultural production in proportion to population growth and water crisis management requires initiatives that can increase the quantity and quality of crops by using soil moisture storage methods while preserving the environment. In this study, the effect of different wt. % of Thermoplastic starch (TPS) with maleic anhydride (MA) as compatibilizer and nanoclay (15A) on gel content and mechanical properties of Polylactic acid (PLA) and blends of Linear low-density polyethylene/ Low-density polyethylene (LLDPE / LDPE) was evaluated.

Research approach: Here, 0, 10, 20 and 30 wt. % TPS were added to the blends of LLDPE/LDPE (20/80) and also PLA. Independent parameters in the experimental design were wt. % of TPS, basic polymer type that was PLA or TPS and aging test. For dependent parameters were considered gel content, tensile strength, elongation at break and elastic modulus. Experiments were designed in General Full Factorial Design and performed in three replications.

Main results: Gel content in LLDPE/LDPE blends increased with the addition of TPS and decreased for PLA blends. The gel content change range for experimental samples before and after the aging test was between 10 to 21 and 2 to 5 percent, respectively. Tensile strength and elongation at break were reduced by adding TPS in both series of compounds before aging test. But this reducing rate was less in the 20 wt. % of TPS. The values of tensile strength and elongation at break were: 12 to 19 MPa and 50 to 350 percent, respectively. These values changed after the aging test between 7 and 11 MPa and from zero to 5 percent, respectively.

Keywords: biodegradability, low density polyethylene, poly lactic acid, thermoplastic starch.

Keywords

biodegradability

low density polyethylene

poly lactic acid

thermoplastic starch

Subjects

Processing

References
1. Tindall, J.A., R. Beverly, and D. Radcliffe, Mulch effect on soil properties and tomato growth using micro-irrigation. Agronomy journal, 1991. 83(6): p. 1028-1034.
2. Díaz-Pérez, J.C., R. Gitaitis, and B. Mandal, Effects of plastic mulches on root zone temperature and on the manifestation of tomato spotted wilt symptoms and yield of tomato. Scientia horticulturae, 2007. 114(2): p. 90-95.
3. Buchholz, K. The Biggest Exporters of Plastic Waste in the World. 2019; Available from: https://www.statista.com/chart/18229/biggest-exporters-of-plastic-waste-and-scrap/.
4. Geyer, R., J.R. Jambeck, and K.L. Law, Production, use, and fate of all plastics ever made. Science Advances, 2017. 3(7).
5. Davis, G. and J. Song, Biodegradable packaging based on raw materials from crops and their impact on waste management. Industrial crops and products, 2006. 23(2): p. 147-161.
6. Takahashi, Y., Cellulose nanoparticles: A route from renewable resources to biodegradable nanocomposites. 2007, State University of New York College of Environmental Science and Forestry.
7. Peyman Jafari, Hamid Mollazini, and M. Silisspoor, Investigation Effect of Cantaloupe Planting Pattern in two Methods of Traditional and Use Mulch. 2, 2007. 2(2): p. 0-0.
8. Mohammad Shahabi Ghoyonloe, M.K., Hassan Sadrnia, Comparison of optical and mechanical properties polyethylene and biodegradableand mulches, in 11th national congress on biosystem engineering and mecanization. 2018, Bu-Ali Sina University: hamedan iran.
9. Touchaleaume, F., et al., Performance and environmental impact of biodegradable polymers as agricultural mulching films. Chemosphere, 2016. 144: p. 433-439.
10. Costa, R., et al., The use of biodegradable mulch films on strawberry crop in Portugal. Scientia Horticulturae, 2014. 173: p. 65-70.
11. Hongsriphan, N. and A. Pinpueng, Properties of Agricultural Films Prepared from Biodegradable Poly (Butylene Succinate) Adding Natural Sorbent and Fertilizer. Journal of Polymers and the Environment, 2019. 27(2): p. 434-443.
12. Sforzini, S., et al., Application of biotests for the determination of soil ecotoxicity after exposure to biodegradable plastics. Frontiers in Environmental Science, 2016. 4: p. 68.
13. Briassoulis, D., Mechanical behaviour of biodegradable agricultural films under real field conditions. Polymer Degradation and Stability, 2006. 91(6): p. 1256-1272.
14. Briassoulis, D., An overview on the mechanical behaviour of biodegradable agricultural films. Journal of Polymers and the Environment, 2004. 12(2): p. 65-81.
15. Brodhagen, M., et al., Biodegradable plastic agricultural mulches and key features of microbial degradation. Applied microbiology and biotechnology, 2015. 99(3): p. 1039-1056.
16. Feuilloley, P., et al., Degradation of polyethylene designed for agricultural purposes. Journal of Polymers and the Environment, 2005. 13(4): p. 349-355.
17. Akrami, M., et al., A new approach in compatibilization of the poly (lactic acid)/thermoplastic starch (PLA/TPS) blends. Carbohydrate polymers, 2016. 144: p. 254-262.
18. Suyatma, N.E., et al., Mechanical and barrier properties of biodegradable films made from chitosan and poly (lactic acid) blends. Journal of Polymers and the Environment, 2004. 12(1): p. 1-6.
19. Zhang, Y., J. Han, and G. Kim, Biodegradable Mulch Film Made of Starch‐Coated Paper and Its Effectiveness on Temperature and Moisture Content of Soil. Communications in soil science and plant analysis, 2008. 39(7-8): p. 1026-1040.
20. Abdollahi Moghaddam, M.R., S.M.A. Razavi, and Y. Jahani, Optimization of the Effects of Thermoplastic Starch and Glycerol Concentration on Physicomechanical Properties of Polylactic acid/Thermoplastic Starch Blend by Response Surface Methodology. Research and Innovation in Food Science and Technology, 2018. 7(3): p. 309-322.
21. Ahmed, J., et al., Starch-Based Polymeric Materials and Nanocomposites: Chemistry, Processing, and Applications. 2012: Taylor & Francis.
22. Sailaja, R.R.N., A.P. Reddy, and M. Chanda, Effect of epoxy functionalized compatibilizer on the mechanical properties of low‐density polyethylene/plasticized tapioca starch blends. Polymer international, 2001. 50(12): p. 1352-1359.
23. Taguet, A., M.A. Huneault, and B.D. Favis, Interface/morphology relationships in polymer blends with thermoplastic starch. Polymer, 2009. 50(24): p. 5733-5743.
24. Wootthikanokkhan, J., et al., Effect of blending conditions on mechanical, thermal, and rheological properties of plasticized poly (lactic acid)/maleated thermoplastic starch blends. Journal of Applied Polymer Science, 2012. 124(2): p. 1012-1019.
25. Huneault, M.A. and H. Li, Morphology and properties of compatibilized polylactide/thermoplastic starch blends. Polymer, 2007. 48(1): p. 270-280.
26. Sawyer, D.J. Bioprocessing–no longer a field of dreams. in Macromolecular symposia. 2003. Wiley Online Library.
27. Mortazavi, S., A. Oromiehie, and I. Ghasemi, Investigation of mechanical, rheological and biodegradation properties of low density polyethylene/thermoplastic starch/nanoclay, in Faculty of processing. 2013, Iran Polymer and Petrochemical Institute: Tehran, Iran. p. 151.
28. Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials, ASTM, G154-00a, in ASTM, Conshohoken, USA. 2000.
29. Ireland, N.S.A.o. and E.C.f. Standardization, CEN EN ISO 527-3. 1996: National Standards Authority of Ireland.
30. standard, E., Plastics Mulching thermoplastic films for use in agriculture and horticulture. 2003, AFNOR — French standard institute. p. 22.
31. Khankrua, R., et al., Development of PLA/EVA Reactive Blends for Heat-Shrinkable Film. Polymers, 2019. 11(12): p. 1925.
32. Wu, J., et al., Effect of gel content on polymer diffusion in poly (vinyl acetate-co-dibutyl maleate) latex films. Macromolecules, 2004. 37(11): p. 4247-4253.
33. Yamoum, C., J. Maia, and R. Magaraphan, Rheological and thermal behavior of PLA modified by chemical crosslinking in the presence of ethoxylated bisphenol A dimethacrylates. Polymers for Advanced Technologies, 2017. 28(1): p. 102-112.
34. Zhang, X.-h., et al., Influence of crosslinking on physical properties of low density polyethylene. Chinese Journal of Polymer Science, 2012. 30(6): p. 837-844.
35. Andreopoulos, A. and E. Kampouris, Mechanical properties of crosslinked polyethylene. Journal of applied polymer science, 1986. 31(4): p. 1061-1068.
36. Scott, G., Abiotic control of polymer biodegradation. Trends in Polymer Science, 1997. 11(5): p. 361-368.
37. Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation, ASTM, D 6954. 2004.
38. Mortazavi, S., I. Ghasemi, and A. Oromiehie, Effect of phase inversion on the physical and mechanical properties of low density polyethylene/thermoplastic starch. Polymer Testing, 2013. 32(3): p. 482-491.
39. Sabetzadeh, M., R. Bagheri, and M. Massomi, Preparation and Study on the Properties of LDPE-Thermoplastic Starch Blends; Part I: Effect of PE-g-MA on the Mechanical Properties and Flow Behavior. Nashrieh Shimi va Mohandesi Shimi Iran, 2013. 32(4): p. 59-69.
40. Beg, M., et al., Preparation and Characterization of Low‐Density Polyethylene/Thermoplastic Starch Composites. Advances in Polymer Technology, 2016. 35(1).
41. Hanifi, S., et al., The Effect Corn Strach and Monmoritlonite Nanocomposites Reinforeced Polypropylene: Preparation and Investigation of the Properties and Biodegradability. J. Vinyl Add. Technol, 2012.
42. Arroyo, O., et al., Processing and properties of PLA/thermoplastic starch/montmorillonite nanocomposites. Polymer Composites, 2010. 31(1): p. 114-127.
43. Hanifi, S., S. Ahmadi, and A. Oromiehie, Mechanical Properties and Biodegradability of Polypropylene/Starch Reinforced Nanoclay Blends. Iranian Journal of Polymer Science and Technology, 2013. 26(2): p. 139-148.
44. Shafiee Nasab, M., M. Tabari, and M.H. Azizi, Morphological and mechanical properties of Poly (lactic Acid)/zinc oxide nanocomposite films. Nanomedicine Research Journal, 2018. 3(2): p. 96-101.
45. Salaberria, A., et al., The antifungal activity of functionalized chitin nanocrystals in poly (Lactid acid) films. Materials, 2017. 10(5): p. 546.
46. Kiangkitiwan, N. and K. Srikulkit, Poly (lactic acid) filled with cassava starch-g-soybean oil maleate. The Scientific World Journal, 2013. 2013.
47. Zhang, Y. and J. Han, Mechanical and thermal characteristics of pea starch films plasticized with monosaccharides and polyols. Journal of food science, 2006. 71(2): p. E109-E118.
48. Kormin, S., et al. Physical and mechanical properties of LDPE incorporated with different starch sources. in IOP Conference Series: Materials Science and Engineering. 2017. IOP Publishing.
49. Yamak, H.B., Thermal, mechanical and water resistance properties of LDPE/starch bio-based polymer blends for food packing applications. Journal of the Turkish Chemical Society, Section A: Chemistry, 2016. 3(3): p. 637-656.
50. Cho, K., et al., Rheological and mechanical properties in polyethylene blends. Polymer Engineering & Science, 1998. 38(12): p. 1969-1975.
51. Micic, P., S. Bhattacharya, and G. Field, Transient elongational viscosity of LLDPE/LDPE blends and its relevance to bubble stability in the film blowing process. Polymer Engineering & Science, 1998. 38(10): p. 1685-1693.
52. Farah, S., D.G. Anderson, and R. Langer, Physical and mechanical properties of PLA, and their functions in widespread applications—A comprehensive review. Advanced drug delivery reviews, 2016. 107: p. 367-392.
53. Joseph, P., et al., Environmental effects on the degradation behaviour of sisal fibre reinforced polypropylene composites. composites science and technology, 2002. 62(10-11): p. 1357-1372.